Loading (50 kb)...'
(continued)
a.2. “Source code” for the “real time processing” of acoustic data for passive reception using towed hydrophone arrays;
a.3. “Software” specially designed for acoustic beam forming for the “real time processing” of acoustic data for passive reception using bottom or bay cable systems;
a.4. “Source code” for the “real time processing” of acoustic data for passive reception using bottom or bay cable systems;
b. Optical sensors. None.
c. Cameras. None.
d. Optics. None.
e. Lasers. None
f. Magnetometers.
f.1. “Software” specially designed for magnetic compensation systems for magnetic sensors designed to operate on mobile platforms;
f.2. “Software” specially designed for magnetic anomaly detection on mobile platforms;
g. Gravimeters. “Software” specially designed to correct motional influences of gravity meters or gravity gradiometers;
h. Radar “software”, as follows:
h.1. Air Traffic Control “software” application “programs” hosted on general purpose computers located at Air Traffic Control centers and capable of any of the following:
h.1.a. Processing and displaying more than 150 simultaneous “system tracks”; or
h.1.b. Accepting radar target data from more than four primary radars;
h.2. “Software” for the design or “production” of radomes which:
h.2.a. Are specially designed to protect the “electronically steerable phased array antennae” controlled by 6A008.e.; and
h.2.b. Result in an antenna pattern having an “average side lobe level” more than 40 dB below the peak of the main beam level.
Technical Note: “Average side lobe level” in 6D003.h.2.b is measured over the entire array excluding the angular extent of the main beam and the first two side lobes on either side of the main beam.
6D102 “Software” specially designed or modified for the “use” of goods controlled by 6A108.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading
6D103 Software” that processes post-flight, recorded data, enabling determination of vehicle position throughout its flight path, specially designed or modified for “missiles”.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
The list of items controlled is contained in the ECCN heading.
6D991 “Software” Specially Designed for the “Development”, “Production”, or “Use” of Equipment Controlled by 6A002.e, 6A991, 6A996, 6A997, or 6A998.
License Requirements
Reason for Control: RS, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
RS applies to ``software'' for RS Column 1.
equipment controlled by 6A002.e or
6A998.b.
AT applies to entire entry, except AT Column 1.
``software'' for equipment controlled
by 6A991.
AT applies to ``software'' for AT Column 2.
equipment controlled by 6A991.
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value.
Related Controls: N/A.
Related Definitions: N/A.
Items:
The list of items controlled is contained in the ECCN heading.
6D992 “Software” specially designed for the “development” or “production” of equipment controlled by 6A992, 6A994, or 6A995.
License Requirements
Reason for Control: AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading.
6D993 Other “software” not controlled by 6D003.
License Requirements
Reason for Control: AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: Equipment in number; parts and accessories in $ value
Related Controls: N/A
Related Definitions: N/A
Items: a. Air Traffic Control (ATC) “software” application “programs” hosted on general purpose computers located at Air Traffic Control centers, and capable of automatically handing over primary radar target data (if not correlated with secondary surveillance radar (SSR) data) from the host ATC center to another ATC center;
E. Technology
6E001 “Technology” according to the General Technology Note for the “development” of equipment, materials or “software” controlled by 6A (except 6A018, 6A991, 6A992, 6A994, 6A995, 6A996, 6A997, or 6A998), 6B (except 6B995), 6C (except 6C992 or 6C994), or 6D (except 6D991, 6D992, or 6D993.
License Requirements
Reason for Control: NS, MT, NP, RS, CC, AT, UN.
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to ``technology'' for items NS Column 1.
controlled by 6A001 to 6A008, 6B004 to
6B008, 6C002 to 6C005, or 6D001 to
6D003.
MT applies to ``technology'' for items MT Column 1.
controlled by 6A002, 6A007, 6A008,
6A102, 6A107, 6A108, 6B008, 6B108,
6D001, 6D002, 6D102 or 6D103 for MT
reasons.
NP applies to ``technology'' for items NP Column 1.
controlled by 6A003, 6A005, 6A202,
6A203, 6A205, 6A225, 6A226, or 6D001
for NP reasons.
RS applies to ``technology'' for RS Column 1.
equipment controlled by 6A002.a.1,
.a.2, .a.3, .c, or .e, 6A003.b.3 or
.b.4, or 6A008.j.1.
CC applies to ``technology'' for CC Column 1.
equipment controlled by 6A002 for CC
reasons.
AT applies to entire entry............. AT Column 1.
UN applies to ``technology'' for Iraq and Rwanda.
equipment controlled by 6A002 or 6A003
for UN reasons.
------------------------------------------------------------------------
License Requirement Notes: See §743.1 of the EAR for reporting requirements for exports under License Exceptions.
License Exceptions
CIV: N/A
TSR: Yes, except for the following:
(1) Items controlled for MT reasons;
(2) “Technology” for commodities controlled by 6A002.e, 6A004.e, or 6A008.j.1;
(3) “Technology” for “software” specially designed for “space qualified” “laser” radar or Light Detection and Ranging (LIDAR) equipment defined in 6A008.j.1 and controlled by 6D001 or 6D002;
(4) Exports or reexports to destinations outside of Austria, Belgium, Canada, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Japan, Luxembourg, the Netherlands, Portugal, Spain, Sweden, or the United Kingdom of “technology” for the “development” of the following: (a) Items controlled by 6A001.a.1.b.1, 6A001.a.2.a.1, 6A001.a.2.a.2, 6A001.a.2.a.3, 6A001.a.2.a.5, 6A001.a.2.a.6,6A001.a.2.b, 6A001.a.2.e., 6A002.a.1.c, 6A008.l.3, 6B008, 6D003.a; (b) Equipment controlled by 6A001.a.2.c or 6A001.a.2.f when specially designed for real time applications; or (c) “Software” controlled by 6D001 and specially designed for the “development” or “production” of equipment controlled by 6A008.l.3 or 6B008; or
(5) Exports or reexports to Rwanda.
List of Items Controlled
Unit: N/A
Related Controls: “Technology” according to the General Technology Note for the “development” of the following commodities is subject to the export licensing authority of the Department of State, Directorate of Defense Trade Controls (22 CFR part 121): “Space qualified” (1.) Components for optical systems defined in 6A004.c and optical control equipment defined in 6A004.d.1.; (2.) Solid-state detectors defined in 6A002.a.1, “imaging sensors” (e.g., “monospectral imaging sensors” and “multispectral imaging sensors”) defined in 6A002.b.2.b.1, and cryocoolers defined in 6A002.d.1 unless on or after September 23, 2002, the Department of State issues a commodity jurisdiction determination assigning the export licensing authority to the Department of Commerce, Bureau of Industry and Security. See also 6E101, 6E201, and 6E991.
Related Definitions: N/A
Items:
The list of items controlled is contained in the ECCN heading.
6E002 “Technology” according to the General Technology Note for the “production” of equipment or materials controlled by 6A (except 6A018, 6A991, 6A992, 6A994, 6A995, 6A996, 6A997 or 6A998), 6B (except 6B995) or 6C (except 6C992 or 6C994).
License Requirements
Reason for Control: NS, MT, NP, RS, CC, AT, UN.
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to ``technology'' for NS Column 1.
equipment controlled by 6A001 to 6A008,
6B004 to 6B008, or 6C002 to 6C005.
MT applies to ``technology'' for MT Column 1.
equipment controlled by 6A002, 6A007,
6A008, 6A102, 6A107, 6A108, 6B008, or
6B108 for MT reasons.
NP applies to ``technology'' for NP Column 1.
equipment controlled by 6A003, 6A005,
6A202, 6A203, 6A205, 6A225 or 6A226 for
NP reasons.
RS applies to ``technology''for RS Column 1.
equipment controlled by 6A002.a.1,
.a.2, .a.3, .c, or .e, 6A003.b.3 or
.b.4, or 6A008.j.1.
CC applies to ``technology'' for CC Column 1.
equipment controlled by 6A002 for CC
reasons.
AT applies to entire entry.............. AT Column 1.
UN applies to ``technology'' for Iraq and Rwanda.
equipment controlled by 6A002 or 6A003
for UN reasons.
------------------------------------------------------------------------
License Requirement Notes: See §743.1 of the EAR for reporting requirements for exports under License Exceptions.
License Exceptions
CIV: N/A
TSR: Yes, except for the following:
(1) Items controlled for MT reasons;
(2) “Technology” for commodities controlled by 6A002.e, 6A004.e, 6A008.j.1;
(3) Exports or reexports to destinations outside of Austria, Belgium, Canada, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Japan, Luxembourg, the Netherlands, Portugal, Spain, Sweden, or the United Kingdom of “technology” for the “development” of the following: (a) Items controlled by 6A001.a.1.b.1, 6A001.a.2.a.1, 6A001.a.2.a.2, 6A001.a.2.a.3, 6A001.a.2.a.5, 6A001.a.2.a.6, 6A001.a.2.b, and 6A001.a.2.c; and (b) Equipment controlled by 6A001.a.2.e and 6A001.a.2.f when specially designed for real time applications; or (c) “Software” controlled by 6D001 and specially designed for the “development” or “production” of equipment controlled by 6A002.a.1.c, 6A008.l.3 or 6B008; or
(4) Exports or reexports to Rwanda.
List of Items Controlled
Unit: N/A
Related Controls: “Technology” according to the General Technology Note for the “production” of the following commodities is subject to the export licensing authority of the Department of State, Directorate of Defense Trade Controls (22 CFR part 121) when intended for use on a satellite: “Space qualified” (1.) Components for optical systems defined in 6A004.c and optical control equipment defined in 6A004.d.1.; (2.) Solid-state detectors defined in 6A002.a.1, “imaging sensors” (e.g., “monospectral imaging sensors” and “multispectral imaging sensors”) defined in 6A002.b.2.b.1, and cryocoolers defined in 6A002.d.1 unless on or after September 23, 2002, the Department of State issues a commodity jurisdiction determination assigning the export licensing authority to the Department of Commerce, Bureau of Industry and Security. See also 6E992.
Related Definitions: N/A
Items:
The list of items controlled is contained in the ECCN heading.
6E003 Other “technology”, as follows (see List of Items Controlled).
License Requirements
Reason for Control: NS, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: Yes
List of Items Controlled
Unit: N/A
Related Controls: See also 6E993
Related Definitions: N/A
Items:
a. Acoustics. None.
b. Optical sensors. None.
c. Cameras. None.
d. Optics, “technology”, as follows:
d.1. Optical surface coating and treatment “technology” “required” to achieve uniformity of 99.5% or better for optical coatings 500 mm or more in diameter or major axis length and with a total loss (absorption and scatter) of less than 5 × 10-3;
N.B.: See also 2E003.f.
d.2. Optical fabrication “technology” using single point diamond turning techniques to produce surface finish accuracies of better than 10 nm rms on non-planar surfaces exceeding 0.5 m 2 ;
e. Lasers. “Technology” “required” for the “development”, “production” or “use” of specially designed diagnostic instruments or targets in test facilities for “SHPL” testing or testing or evaluation of materials irradiated by “SHPL” beams;
f. Magnetometers. None
g. Gravimeters. None
h. Radar. None
6E101 “Technology” according to the General Technology Note for the “use” of equipment or “software” controlled by 6A002, 6A007.b and .c, 6A008, 6A102, 6A107, 6A108, 6B108, 6D102 or 6D103.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: N/A
Related Controls: N/A
Related Definitions: (1) This entry only controls “technology” for equipment controlled by 6A008 when it is designed for airborne applications and is usable in “missiles”. (2) This entry only controls “technology” for items in 6A002.a.1, a.3, and .e that are specially designed or modified to protect “missiles” against nuclear effects (e.g., Electromagnetic Pulse (EMP), X-rays, combined blast and thermal effects), and usable for “missiles.” (3) This entry only controls “technology” for items in 6A007.b and .c when the accuracies in 6A007.b.1 and b.2 are met or exceeded.
Items: The list of items controlled is contained in the ECCN heading.
6E201 “Technology” according to the General Technology Note for the “use” of equipment controlled by 6A003.a.2. 6A003.a.3, 6A003.a.4, 6A005.a.1.c, 6A005.a.2.a, 6A005.a.4.c, 6A005.a.6, 6A005.c.1.b, 6A005.c.2.b.2.a, 6A005.c.2.b.2.b, 6A005.c.2.c.2, or 6A005.d.2.c., 6A202, 6A203, 6A205, 6A225 or 6A226.
License Requirements
Reason for Control: NP, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NP applies to entire entry............. NP Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: N/A
Related Controls: N/A
Related Definitions: N/A
ECCN Controls: This entry only controls “technology” for “lasers” in 6A005 that are controlled for NP reasons.
Items: The list of items controlled is contained in the ECCN heading.
6E991 “Technology” for the “development”, “production” or “use” of equipment controlled by 6A991, 6A996, 6A997, or 6A998.
License Requirements
Reason for Control: RS, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
RS applies to ``technology'' for RS Column 1.
equipment controlled by 6A998.b.
AT applies to entire entry except AT Column 1.
``technology'' for equipment
controlled by 6A991.
AT applies to ``technology'' for AT Column 2.
equipment controlled by 6A991.
------------------------------------------------------------------------
License Exceptions
CIV: N/A.
TSR: N/A.
List of Items Controlled
Unit: N/A.
Related Controls: N/A.
Related Definitions: N/A.
Items:
The list of items controlled is contained in the ECCN heading.
6E992 “Technology” for the “development” or “production” of equipment, materials or “software” controlled by 6A992, 6A994, or 6A995, 6B995, 6C992, 6C994, or 6D993.
License Requirements
Reason for Control: AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading.
6E993 Other “technology”, not controlled by 6E003, as follows (see List of Items Controlled).
License Requirements
Reason for Control: AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: N/A
Related Controls: N/A
Related Definitions: N/A
Items: a. Optical fabrication technologies for serially producing optical components at a rate exceeding 10 m 2 of surface area per year on any single spindle and with:
a.1. An area exceeding 1 m 2 ; and
a.2. A surface figure exceeding lambda/10 rms at the designed wavelength;
b. “Technology” for optical filters with a bandwidth equal to or less than 10 nm, a field of view (FOV) exceeding 40° and a resolution exceeding 0.75 line pairs per milliradian;
c. “Technology” for the “development” or “production” of cameras controlled by 6A993;
d. “Technology” “required” for the “development” or “production” of non-triaxial fluxgate “magnetometers” or non-triaxial fluxgate “magnetometer” systems, having any of the following:
d.1. A “noise level” of less than 0.05 nT rms per square root Hz at frequencies of less than 1 Hz; or
d.2. A “noise level” of less than 1 × 10-3 nT rms per square root Hz at frequencies of 1 Hz or more.
EAR99 Items subject to the EAR that are not elsewhere specified in this CCL Category or in any other category in the CCL are designated by the number EAR99.
Category 7—Navigation and Avionics
A. Systems, Equipment and Components
N.B. 1: For automatic pilots for underwater vehicles, see Category 8. For radar, see Category 6.
7A001 Linear Accelerometers Designed for Use in Inertial Navigation or Guidance Systems and Having Any of the Following Characteristics (See List of Items Controlled), and Specially Designed Components Therefor
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value.
Related Controls: See also 7A101 and 7A994. For angular or rotational accelerometers, see 7A002. MT controls do not apply to accelerometers that are specially designed and developed as Measurement While Drilling (MWD) sensors for use in downhole well service applications.
Related Definitions: N/A.
Items:
a. A “bias” “stability” of less (better) than 130 micro g with respect to a fixed calibration value over a period of one year;
b. A “scale factor” “stability” of less (better) than 130 ppm with respect to a fixed calibration value over a period of one year; or
c. Specified to function at linear acceleration levels exceeding 100 g.
7A002 Gyros, and Angular or Rotational Accelerometers, Having Any of the Following Characteristics (See List of Items Controlled), and Specially Designed Components Therefor
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1.
MT applies to, commodities described in MT Column 1.
this entry that meet the parameters of
7A102.
AT applies to entire entry............. AT Column 1.
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value.
Related Controls: See also 7A102 and 7A994. For linear accelerometers, see 7A001.
Related Definitions: N/A.
Items:
a. A “drift rate” “stability”, when measured in a 1 g environment over a period of one month and with respect to a fixed calibration value, of:
a.1. Less (better) than 0.1 degree per hour when specified to function at linear acceleration levels below 12 g; or
a.2. Less (better) than 0.5 degree per hour when specified to function at linear acceleration levels from 12 g to 100 g inclusive;
b. An angle random walk of less (better) than or equal to 0.0035 degree per square root hour; or
Note: 7A002.b does not control spinning mass gyros (spinning mass gyros are gyros which use a continually rotating mass to sense angular motion).
Technical Note: For the purpose of 7A002.b, “angle random walk” is the angular error buildup with time that is due to white noise in angular rate. (IEEE STD 528–2001).
c. Specified to function at linear acceleration levels exceeding 100 g.
7A003 Inertial Systems and specially designed components therefor.
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: See also 7A103 and 7A994. Inertial Navigation Systems (INS) and inertial equipment, and specially designed components therefor specifically designed, modified or configured for military use are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. (See 22 CFR part 121.)
Related Definitions: “Data-Based Referenced Navigation” (“DBRN”) systems are systems which use various sources of previously measured geo-mapping data integrated to provide accurate navigation information under dynamic conditions. Data sources include bathymetric maps, stellar maps, gravity maps, magnetic maps or 3–D digital terrain maps.
Items: a. Inertial Navigation Systems (INS) (gimballed or strapdown) and inertial equipment designed for “aircraft”, land vehicles, vessels (surface or underwater) or “spacecraft” for attitude, guidance or control, having any of the following characteristics, and specially designed components therefor:
a.1. Navigation error (free inertial) subsequent to normal alignment of 0.8 nautical mile per hour (nm/hr) Circular Error Probable (CEP) or less (better); or
a.2. Specified to function at linear acceleration levels exceeding 10 g.
b. Hybrid Inertial Navigation Systems embedded with Global Navigation Satellite System(s) (GNSS) or with “Data-Based Referenced Navigation” (“DBRN”) System(s) for attitude, guidance or control, subsequent to normal alignment, having an INS navigation position accuracy, after loss of GNSS or “DBRN” for a period of up to 4 minutes, of less (better) than 10 meters Circular Error Probable (CEP).
c. Inertial Equipment for Azimuth, Heading, or North Pointing having any of the following characteristics, and specially designed components therefor:
c.1. Designed to have an Azimuth, Heading, or North Pointing accuracy equal to, or less (better) than 6 arc minutes RMS at 45 degrees latitude; or
c.2. Designed to have a non-operating shock level of 900 g or greater at a duration of 1-msec, or greater.
Note 1: The parameters of 7A003.a and 7A003.b are applicable with any of the following environmental conditions:
1. Input random vibration with an overall magnitude of 7.7 g rms in the first half hour and a total test duration of one and one half hour per axis in each of the three perpendicular axes, when the random vibration meets the following:
a. A constant power spectral density (PSD) value of 0.04 g 2 /Hz over a frequency interval of 15 to 1,000 Hz; and
b. The PSD attenuates with frequency from 0.04 g 2 /Hz to 0.01 g 2 /Hz over a frequency interval from 1,000 to 2,000 Hz;
2. A roll and yaw rate of equal to or more than +2.62 rad/s (150 deg/s); or
3. According to national standards equivalent to 1. or 2. of this note.
Note 2: 7A003 does not control inertial navigation systems that are certified for use on “civil aircraft” by civil authorities of a country in Country Group A:1.
Note 3: 7A003.c.1 does not control theodolite systems incorporating inertial equipment specially designed for civil surveying purposes.
Technical Notes: 1. 7A003.b refers to systems in which an INS and other independent navigation aids are built into a single unit (embedded) in order to achieve improved performance.
2. “Circular Error Probable” (“CEP”)—In a circular normal distribution, the radius of the circle containing 50 percent of the individual measurements being made, or the radius of the circle within which there is a 50 percent probability of being located.
7A004 Gyro-astro compasses, and other devices which derive position or orientation by means of automatically tracking celestial bodies or satellites, with an azimuth accuracy of equal to or less (better) than 5 seconds of arc.
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: See also 7A104 and 7A994
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading.
7A005 Global navigation satellite systems (i.e. GPS or GLONASS) receiving equipment, and specially designed components therefor. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
Note to 7A005: See also 7A105 and 7A994.
7A006 Airborne altimeters operating at frequencies other than 4.2 to 4.4 GHz inclusive, having any of the following characteristics (see List of Items Controlled).
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: See also 7A106, 7A994 and Category 6 for controls on radar.
Related Definitions: N/A
Items: a. “Power management”; or
b. Using phase shift key modulation.
7A102 All types of gyros, other than those controlled by 7A002, usable in “missiles”, with a rated “drift rate” “stability” of less than 0.5° (1 sigma or rms) per hour in a 1 g environment and specially designed components therefor.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: N/A
Related Definitions: (1) Drift rate is defined as the time rate of output deviation from the desired output. It consists of random and systematic components and is expressed as an equivalent angular displacement per unit time with respect to inertial space. (2) Stability is defined as standard deviation (1 sigma) of the variation of a particular parameter from its calibrated value measured under stable temperature conditions. This can be expressed as a function of time.
Items: The list of items controlled is contained in the ECCN heading.
7A103 Instrumentation, navigation equipment and systems, other than those controlled by 7A003, and specially designed components therefor.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: (1) Items described in 7A103.b are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls (See 22 CFR part 121). (2) Inertial navigation systems and inertial equipment, and specially designed components therefor specifically designed, modified or configured for military use are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. (See 22 CFR part 121.)
Related Definitions: N/A
Items: a. Inertial or other equipment using accelerometers or gyros controlled by 7A001, 7A002, 7A101 or 7A102 and systems incorporating such equipment;
Note: 7A103.a does not control equipment containing accelerometers specially designed and developed as MWD (Measurement While Drilling) sensors for use in down-hole well services operations.
b. Integrated flight instrument systems, which include gyrostabilizers or automatic pilots, designed or modified for use in “missiles”.
c. Integrated Navigation Systems, designed or modified for use in “missiles” and capable of providing a navigational accuracy of 200m Circular Error Probable (CEP) or less.
Technical Note: An ‘integrated navigation system’ typically incorporates the following components:
1. An inertial measurement device (e.g., an attitude and heading reference system, inertial reference unit, or inertial navigation system);
2. One or more external sensors used to update the position and/or velocity, either periodically or continuously throughout the flight (e.g., satellite navigation receiver, radar altimeter, and/or Doppler radar); and
3. Integration hardware and software.
7A104 Gyro-astro compasses and other devices, other than those controlled by 7A004, which derive position or orientation by means of automatically tracking celestial bodies or satellites and specially designed components therefor.
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: This entry controls specially designed components for gyro-astro compasses and other devices controlled by 7A004
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading.
7A105 Receiving equipment for Global Navigation Satellite Systems (GNSS) (e.g. GPS, GLONASS, or Galileo) having any of the following characteristics, and specially designed components therefor. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
1. Designed or modified for use in “missiles”; or
2. Designed or modified for airborne applications and having any of the following:
a. Capable of providing navigation information at speeds in excess of 600 m/s (1,165 nautical mph).
b. Employing decryption, designed or modified for military or governmental services, to gain access to GNSS secured signal/data; or
c. Being specially designed to employ anti-jam features (e.g. null steering antenna or electronically steerable antenna) to function in an environment of active or passive countermeasures.
Note to 7A105: See also 7A005 and 7A994.
7A106 Altimeters, other than those controlled by 7A006, of radar or laser radar type, designed or modified for use in “missiles”. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
7A115 Passive sensors for determining bearing to specific electromagnetic source (direction finding equipment) or terrain characteristics, designed or modified for use in “missiles”. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
7A116 Flight control systems (hydraulic, mechanical, electro-optical, or electro-mechanical flight control systems (including fly-by-wire systems) and attitude control equipment) designed or modified for “missiles”. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
7A117 “Guidance sets” capable of achieving system accuracy of 3.33% or less of the range (e.g., a “CEP” of 10 km or less at a range of 300 km). (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
7A994 Other navigation direction finding equipment, airborne communication equipment, all aircraft inertial navigation systems not controlled under 7A003 or 7A103, and other avionic equipment, including parts and components, n.e.s.
License Requirements
Reason for Control: RS, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
RS applies to QRS11-00100-100/101 RS Column 1
Micromachined Angular Rate Sensors
when exported solely for integration
into a CSIS controlled in this entry.
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Requirement Notes: There is no de minimis level for foreign-made Commercial Standby Instrument Systems (CSIS) that integrate QRS11–00100–100/101 Micromachined Angular Rate Sensors (see §734.4(a) of the EAR).
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: QRS11 Micromachined Angular Rate Sensors are subject to the export licensing jurisdiction of the U.S. Department of State, Directorate of Defense Trade Controls, unless the QRS11–00100–100/101 is integrated into and included as an integral part of a CSIS of the type described in ECCN 7A994 or aircraft of the type described in ECCN 9A991 that incorporates a CSIS that has such a sensor integrated, or is exported solely for integration into such a system (See 22 CFR Part 121). In the latter case, such items are subject to the licensing jurisdiction of the Department of Commerce. Technology specific to the development and production of QRS11 sensors remains subject to the licensing jurisdiction of the Department of State.
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading.
B. Test, Inspection and Production Equipment
7B001 Test, calibration or alignment equipment specially designed for equipment controlled by 7A (except 7A994).
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: (1) See also 7B101, 7B102 and 7B994.
(2) This entry does not control test, calibration or alignment equipment for Maintenance level I.
Related Definition: (1) Maintenance Level I: The failure of an inertial navigation unit is detected on the aircraft by indications from the Control and Display Unit (CDU) or by the status message from the corresponding sub-system. By following the manufacturer's manual, the cause of the failure may be localized at the level of the malfunctioning line replaceable unit (LRU). The operator then removes the LRU and replaces it with a spare. (2) Maintenance Level II: The defective LRU is sent to the maintenance workshop (the manufacturer's or that of the operator responsible for level II maintenance). At the maintenance workshop, the malfunctioning LRU is tested by various appropriate means to verify and localize the defective shop replaceable assembly (SRA) module responsible for the failure. This SRA is removed and replaced by an operative spare. The defective SRA (or possibly the complete LRU) is then shipped to the manufacturer. Maintenance Level II does not include the removal of controlled accelerometers or gyro sensors from the SRA.
Items: The list of items controlled is contained in the ECCN heading.
7B002 Equipment, as follows (see List of Items Controlled), specially designed to characterize mirrors for ring “laser” gyros.
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: See also 7B102 and 7B994
Related Definitions: N/A
Items: a. Scatterometers having a measurement accuracy of 10 ppm or less (better);
b. Profilometers having a measurement accuracy of 0.5 nm (5 angstrom) or less (better).
7B003 Equipment specially designed for the “production” of equipment controlled by 7A (except 7A994).
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value.
Related Controls: (1) See also 7B103, (this entry is subject to the licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls (see 22 CFR part 121)) and 7B994.
(2) This entry includes: Inertial Measurement Unit (IMU module) tester; IMU platform tester; IMU stable element handling fixture; IMU platform balance fixture; gyro tuning test station; gyro dynamic balance station; gyro run-in/motor test station; gyro evacuation and fill station; centrifuge fixtures for gyro bearings; accelerometer axis align station; and accelerometer test station.
Related Definitions: N/A.
Items: The list of items controlled is contained in the ECCN heading.
7B101 Production equipment”, and other test, calibration, and alignment equipment, other than that described in 2B119 to 2B122, 7B003, and 7B102, designed or modified to be used with equipment controlled by 7A001 to 7A004 or 7A101 to 7A104.
License Requirements
Reason for Control: MT, AT.
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1.
AT applies to entire entry............. AT Column 1.
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value.
Related Controls: (1) See also 2B119 to 2B122, 7B003, 7B102, and 7B994.
(2) This entry includes: inertial measurement unit (IMU module) tester; IMU platform tester; IMU stable element handling fixture; IMU platform balance fixture; gyro tuning test station; gyro dynamic balance stations; gyro run-in/motor test stations; gyro evacuation and filling stations; centrifuge fixtures for gyro bearings; accelerometer axis align stations; and accelerometer test stations.
Related Definitions: N/A.
Items: The list of items controlled is contained in the ECCN heading.
7B102 Equipment, other than those controlled by 7B002, designed or modified to characterize mirrors, for laser gyro equipment, as follows (see List of Items Controlled).
License Requirements
Reason for Control: MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value.
Related Controls: N/A.
Related Definitions: N/A.
Items:
a. Scatterometers having a threshold accuracy of 10 ppm or less (better).
b. Reflectometers having a threshold accuracy of 50 ppm or less (better).
c. Prolifometers having a threshold accuracy of 0.5nm (5 angstrom) or less (better).
7B103 Specially designed “production facilities” for equipment controlled by 7A117. (These items are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. See 22 CFR part 121.)
7B994 Other equipment for the test, inspection, or “production” of navigation and avionics equipment.
License Requirements
Reason for Control: AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
LVS: N/A
GBS: N/A
CIV: N/A
List of Items Controlled
Unit: $ value
Related Controls: N/A
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading
C. Materials [Reserved]
D. Software
7D001 “Software” specially designed or modified for the “development” or “production” of equipment controlled by 7A (except 7A994) or 7B (except 7B994).
License Requirements
Reason for Control: NS, MT, RS, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to ``software'' for NS Column 1
equipment controlled by 7A001 to
7A004, 7A006, 7B001, 7B002 or 7B003.
MT applies to entire entry............. MT Column 1
RS applies to ``software'' for inertial
navigation systems inertial equipment,
and specially designed components
therefor, for ``civil aircraft'' DRS
Column 1.
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
Related Controls: (1) See also 7D101 and 7D994. (2) The “software” related to 7A003.b, 7A005, 7A007, 7A103.b, 7A105, 7A106, 7A115, 7A116, 7A117, or 7B103 are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. (See 22 CFR part 121.) (3) “Software” for inertial navigation systems and inertial equipment, and specially designed components therefor, not for use on civil aircraft are subject to the export licensing authority of the U.S. Department of State, Directorate of Defense Trade Controls. (See 22 CFR part 121.)
Related Definitions: N/A
Items: The list of items controlled is contained in the ECCN heading
7D002 “Source code” for the “use” of any inertial navigation equipment including inertial equipment not controlled by 7A003 or 7A004, or Attitude and Heading Reference Systems (AHRS) (except gimballed AHRS).
License Requirements
Reason for Control: NS, MT, AT
------------------------------------------------------------------------
Control(s) Country chart
------------------------------------------------------------------------
NS applies to entire entry............. NS Column 1
MT applies to entire entry............. MT Column 1
AT applies to entire entry............. AT Column 1
------------------------------------------------------------------------
License Exceptions
CIV: N/A
TSR: N/A
List of Items Controlled
Unit: $ value
Related Controls: (1) See also 7D102 and 7D994. (2) This entry does not control “source code” for the “use” of gimballed AHRS
Related Definition: AHRS generally differ from inertial navigation systems (INS) in that an AHRS provides attitude and heading information and normally does not provide the acceleration, velocity and position information associated with an INS
Items: The list of items controlled is contained in the ECCN heading
7D003 Other “software”, as follows (see List of Items Controlled).
License Requirements
Reason forControl: NS, MT, AT (continued)