National United States Regulations 40 CFR PART 442—TRANSPORTATION EQUIPMENT CLEANING POINT SOURCE CATEGORY PART 442—TRANSPORTATION EQUIPMENT CLEANING POINT SOURCE CATEGORY -------------------------------------------------------------------------------- Authority: 33 U.S.C. 1311, 1314, 1316, 1317, 1318, 1342 and 1361. Source: 65 FR 49700, Aug. 14, 2000, unless otherwise noted. § 442.1 General applicability. top (a) As defined more specifically in each subpart, and except for discharges specified in paragraph (b) of this section, this part applies to discharges resulting from cleaning the interior of tanks used to transport chemical, petroleum or food grade cargos. This part does not apply to facilities that clean only the exteriors of transportation equipment. Operations which may be subject to this part typically are reported under a wide variety of Standard Industrial Classification (SIC) codes. Several of the most common SIC codes include: SIC 7699, SIC 4741, or SIC 4491 (1987 SIC Manual). (b) This part is not applicable to the following discharges: (1) Wastewaters associated with tank cleanings operated in conjunction with other industrial, commercial, or Publicly Owned Treatment Works (POTW) operations, provided that the cleaning is limited to tanks that previously contained raw materials, by-products, or finished products that are associated with the facility's on-site processes. (2) Wastewaters resulting from cleaning the interiors of drums, intermediate bulk containers, or closed-top hoppers. (3) Wastewater from a facility that discharges less than 100,000 gallons per year of transportation equipment cleaning process wastewater. § 442.2 General definitions. top (a) In addition to the general definitions and abbreviations at 40 CFR part 401, the following definitions shall apply to this part: Chemical cargos mean, but are not limited to, the following: latex, rubber, plastics, plasticizers, resins, soaps, detergents, surfactants, agricultural chemicals and pesticides, hazardous waste, organic chemicals including: alcohols, aldehydes, formaldehydes, phenols, peroxides, organic salts, amines, amides, other nitrogen compounds, other aromatic compounds, aliphatic organic chemicals, glycols, glycerines, and organic polymers; refractory organic compounds including: ketones, nitriles, organo-metallic compounds containing chromium, cadmium, mercury, copper, zinc; and inorganic chemicals including: aluminum sulfate, ammonia, ammonium nitrate, ammonium sulfate, and bleach. Cargos which are not considered to be food grade or petroleum cargos are considered to be chemical cargos. Closed-top hopper means a completely enclosed storage vessel used to transport dry bulk cargos, either by truck, rail, or barge. Closed-top hoppers are not designed or constructed to carry liquid cargos and are typically used to transport grain, soybeans, soy meal, soda ash, lime, fertilizer, plastic pellets, flour, sugar, and similar commodities or cargos. The cargos transported come in direct contact with the hopper interior. Closed-top hoppers are also commonly referred to as dry bulk hoppers. Drums mean metal or plastic cylindrical containers with either an open-head or a tight-head (also known as bung-type top) used to hold liquid, solid, or gaseous commodities or cargos which are in direct contact with the container interior. Drums typically range in capacity from 30 to 55 gallons. Food grade cargos mean edible and non-edible food products. Specific examples of food grade cargos include, but are not limited to, the following: alcoholic beverages, animal by-products, animal fats, animal oils, caramel, caramel coloring, chocolate, corn syrup and other corn products, dairy products, dietary supplements, eggs, flavorings, food preservatives, food products that are not suitable for human consumption, fruit juices, honey, lard, molasses, non-alcoholic beverages, sweeteners, tallow, vegetable oils, and vinegar. Heel means any material remaining in a tank following unloading, delivery, or discharge of the transported cargo. Heels may also be referred to as container residue, residual materials or residuals. Intermediate bulk container (“IBC” or “Tote”) means a completely enclosed storage vessel used to hold liquid, solid, or gaseous commodities or cargos which are in direct contact with the container interior. IBCs may be loaded onto flat beds for either truck or rail transport, or onto ship decks for water transport. IBCs are portable containers with 450 liters (119 gallons) to 3000 liters (793 gallons) capacity. IBCs are also commonly referred to as totes or tote bins. Intermodal tank container means a completely enclosed storage vessel used to hold liquid, solid, or gaseous commodities or cargos which come in direct contact with the tank interior. Intermodal tank containers may be loaded onto flat beds for either truck or rail transport, or onto ship decks for water transport. Containers larger than 3000 liters capacity are considered intermodal tank containers. Containers smaller than 3000 liters capacity are considered IBCs. Ocean/sea tanker means a self or non-self-propelled vessel constructed or adapted to transport liquid, solid or gaseous commodities or cargos in bulk in cargo spaces (or tanks) through oceans and seas, where the commodity or cargo carried comes in direct contact with the tank interior. There are no maximum or minimum vessel or tank volumes. On-site means within the contiguous and non-contiguous established boundaries of a facility. Petroleum cargos mean products of the fractionation or straight distillation of crude oil, redistillation of unfinished petroleum derivatives, cracking, or other refining processes. For purposes of this rule, petroleum cargos also include products obtained from the refining or processing of natural gas and coal. For purposes of this rule, specific examples of petroleum products include but are not limited to: asphalt; benzene; coal tar; crude oil; cutting oil; ethyl benzene; diesel fuel; fuel additives; fuel oils; gasoline; greases; heavy, medium, and light oils; hydraulic fluids, jet fuel; kerosene; liquid petroleum gases (LPG) including butane and propane; lubrication oils; mineral spirits; naphtha; olefin, paraffin, and other waxes; tall oil; tar; toluene; xylene; and waste oil. Pollution Prevention Allowable Discharge for this subpart means the quantity of/concentrations of pollutants in wastewaters being discharged to publicly owned treatment works after a facility has demonstrated compliance with the Pollutant Management Plan provisions in §§442.15(b), 442.16(b), 442.25(b), or 442.26(b) of this part. Prerinse/presteam means a rinse, typically with hot or cold water, performed at the beginning of the cleaning sequence to remove residual material from the tank interior. Presolve wash means the use of diesel, kerosene, gasoline, or any other type of fuel or solvent as a tank interior cleaning solution. Rail Tank Car means a completely enclosed storage vessel pulled by a locomotive that is used to transport liquid, solid, or gaseous commodities or cargos over railway access lines. A rail tank car storage vessel may have one or more storage compartments and the stored commodities or cargos come in direct contact with the tank interior. There are no maximum or minimum vessel or tank volumes. Tank barge means a non-self-propelled vessel constructed or adapted primarily to carry liquid, solid or gaseous commodities or cargos in bulk in cargo spaces (or tanks) through rivers and inland waterways, and may occasionally carry commodities or cargos through oceans and seas when in transit from one inland waterway to another. The commodities or cargos transported are in direct contact with the tank interior. There are no maximum or minimum vessel or tank volumes. Tank truck means a motor-driven vehicle with a completely enclosed storage vessel used to transport liquid, solid or gaseous materials over roads and highways. The storage vessel or tank may be detachable, as with tank trailers, or permanently attached. The commodities or cargos transported come in direct contact with the tank interior. A tank truck may have one or more storage compartments. There are no maximum or minimum vessel or tank volumes. Tank trucks are also commonly referred to as cargo tanks or tankers. Transportation equipment cleaning (TEC) process wastewater means all wastewaters associated with cleaning the interiors of tanks including: tank trucks; rail tank cars; intermodal tank containers; tank barges; and ocean/sea tankers used to transport commodities or cargos that come into direct contact with the interior of the tank or container. At those facilities that clean tank interiors, TEC process wastewater also includes wastewater generated from washing vehicle exteriors, equipment and floor washings, TEC-contaminated stormwater, wastewater prerinse cleaning solutions, chemical cleaning solutions, and final rinse solutions. TEC process wastewater is defined to include only wastewater generated from a regulated TEC subcategory. Therefore, TEC process wastewater does not include wastewater generated from cleaning hopper cars, or from food grade facilities discharging to a POTW. Wastewater generated from cleaning tank interiors for purposes of shipping products (i.e., cleaned for purposes other than maintenance and repair) is considered TEC process wastewater. Wastewater generated from cleaning tank interiors for the purposes of maintenance and repair on the tank is not considered TEC process wastewater. Facilities that clean tank interiors solely for the purposes of repair and maintenance are not regulated under this Part. (b) The parameters regulated in this part and listed with approved methods of analysis in Table IB at 40 CFR 136.3, are defined as follows: (1) BOD5 means 5-day biochemical oxygen demand. (2) Cadmium means total cadmium. (3) Chromium means total chromium. (4) Copper means total copper. (5) Lead means total lead. (6) Mercury means total mercury (7) Nickel means total nickel. (8) Oil and Grease (HEM) means oil and grease (Hexane-Extractable Material) measured by Method 1664. (9) Non-polar material (SGT-HEM) means the non-polar fraction of oil and grease (Silica Gel Treated Hexane-Extractable Material) measured by Method 1664. (10) TSS means total suspended solids. (11) Zinc means total zinc. (c) The parameters regulated in this part and listed with approved methods of analysis in Table IC at 40 CFR 136.3, are as follows: (1) Fluoranthene. (2) Phenanthrene. § 442.3 General pretreatment standards. top Any source subject to this part that introduces process wastewater pollutants into a publicly owned treatment works (POTW) must comply with 40 CFR part 403. Subpart A—Tank Trucks and Intermodal Tank Containers Transporting Chemical and Petroleum Cargos top § 442.10 Applicability. top This subpart applies to discharges resulting from the cleaning of tank trucks and intermodal tank containers which have been used to transport chemical or petroleum cargos. § 442.11 Effluent limitations attainable by the application of the best practicable control technology currently available (BPT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BPT: (a) Effluent Limitations ------------------------------------------------------------------------ Maximum Regulated parameter Maximum monthly daily \1\ avg. \1\ ------------------------------------------------------------------------ BOD5......................................... 61 22 TSS.......................................... 58 26 Oil and grease (HEM)......................... 36 16 Copper....................................... 0.84 ........... Mercury...................................... 0.0031 ........... pH........................................... (\2\) (\2\) ------------------------------------------------------------------------ \1\ Mg/L (ppm) \2\ Within 6 to 9 at all times. § 442.12 Effluent limitations attainable by the application of the best conventional pollutant control technology (BCT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BCT: Limitations for BOD5, TSS, oil and grease (HEM) and pH are the same as the corresponding limitation specified in §442.11. § 442.13 Effluent limitations attainable by the application of best available technology economically achievable (BAT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BAT: Limitations for copper, mercury, and oil and grease (HEM) are the same as the corresponding limitation specified in §442.11. § 442.14 New source performance standards (NSPS). top Any new point source subject to this subpart must achieve the following performance standards: Standards for BOD5, TSS, oil and grease (HEM), copper, mercury, and pH are the same as the corresponding limitation specified in §442.11. § 442.15 Pretreatment standards for existing sources (PSES). top (a) Except as provided in 40 CFR 403.7 and 403.13 or in paragraph (b) of this section, no later than August 14, 2003, any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must achieve PSES as follows: Table_Pretreatment Standards ------------------------------------------------------------------------ Maximum Regulated parameter daily \1\ ------------------------------------------------------------------------ Non-polar material (SGT-HEM).............................. 26 Copper.................................................... 0.84 Mercury................................................... 0.0031 ------------------------------------------------------------------------ \1\ Mg/L (ppm). (b) As an alternative to achieving PSES as defined in paragraph (a) of this section, any existing source subject to paragraph (a) of this section may have a pollution prevention allowable discharge of wastewater pollutants, as defined in §442.2, if the source agrees to control mechanism with the control authority as follows: (1) The discharger shall prepare a Pollutant Management Plan that satisfies the requirements as specified in paragraph (b)(5) of this section, and the discharger shall conduct its operations in accordance with that plan. (2) The discharger shall notify its local control authority prior to renewing or modifying its individual control mechanism or pretreatment agreement of its intent to achieve the pollution prevention allowable discharge pretreatment standard by submitting to the local control authority a certification statement of its intent to utilize a Pollutant Management Plan as specified in paragraph (b)(1) of this section. The certification statement must be signed by the responsible corporate officer as defined in 40 CFR 403.12(l); (3) The discharger shall submit a copy of its Pollutant Management Plan as described in paragraph (b)(1) of this section to the appropriate control authority at the time he/she applies to renew, or modify its individual control mechanism or pretreatment agreement; and (4) The discharger shall maintain at the offices of the facility and make available for inspection the Pollutant Management Plan as described in paragraph (b)(1) of this section. (5) The Pollutant Manager Plan shall include: (i) Procedures for identifying cargos, the cleaning of which is likely to result in discharges of pollutants that would be incompatible with treatment at the POTW; (ii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that heels be fully drained, segregated from other wastewaters, and handled in an appropriate manner; (iii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that the tank be prerinsed or presteamed as appropriate and the wastewater segregated from wastewaters to be discharged to the POTW and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (iv) All spent cleaning solutions, including interior caustic washes, interior presolve washes, interior detergent washes, interior acid washes, and exterior acid brightener washes shall be segregated from other wastewaters and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (v) Provisions for appropriate recycling or reuse of cleaning agents; (vi) Provisions for minimizing the use of toxic cleaning agents (solvents, detergents, or other cleaning or brightening solutions); (vii) Provisions for appropriate recycling or reuse of segregated wastewaters (including heels and prerinse/pre-steam wastes); (viii) Provisions for off-site treatment or disposal, or effective pre-treatment of segregated wastewaters (including heels, prerinse/pre-steam wastes, spent cleaning solutions); (ix) Information on the volumes, content, and chemical characteristics of cleaning agents used in cleaning or brightening operations; and (x) Provisions for maintaining appropriate records of heel management procedures, prerinse/pre-steam management procedures, cleaning agent management procedures, operator training, and proper operation and maintenance of any pre-treatment system; § 442.16 Pretreatment standards for new sources (PSNS). top (a) Except as provided in 40 CFR 403.7 and 403.13 or in paragraph (b) of this section, any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must achieve PSNS as follows: Table_Pretreatment Standards ------------------------------------------------------------------------ Maximum Regulated parameter daily \1\ ------------------------------------------------------------------------ Non-polar material (SGT-HEM).............................. 26 Copper.................................................... 0.84 Mercury................................................... 0.0031 ------------------------------------------------------------------------ \1\ Mg/L (ppm). (b) As an alternative to achieving PSNS as defined in paragraph (a) of this section, any new source subject to paragraph (a) of this section may have a pollution prevention allowable discharge of wastewater pollutants, as defined in §442.2, if the source agrees to a control mechanism with the control authority as follows: (1) The discharger shall prepare a Pollutant Management Plan that satisfies the requirements as specified in paragraph (b)(5) of this section, and the discharger shall conduct its operations in accordance with that plan. (2) The discharger shall notify its local control authority prior to obtaining, renewing, or modifying its individual control mechanism or pretreatment agreement of its intent to achieve the pollution prevention allowable discharge pretreatment standard by submitting to the local control authority a certification statement of its intent to utilize a Pollutant Management Plan as specified in paragraph (b)(1) of this section. The certification statement must be signed by the responsible corporate officer as defined in 40 CFR 403.12(l); (3) The discharger shall submit a copy of its Pollutant Management Plan as described in paragraph (b)(1) of this section to the appropriate control authority at the time he/she applies to renew, or modify its individual control mechanism or pretreatment agreement; and (4) The discharger shall maintain at the offices of the facility and make available for inspection the Pollutant Management Plan as described in paragraph (b)(1) of this section. (5) The Pollutant Management Plan shall include: (i) Procedures for identifying cargos, the cleaning of which is likely to result in discharges of pollutants that would be incompatible with treatment at the POTW; (ii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that heels be fully drained, segregated from other wastewaters, and handled in an appropriate manner; (iii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that the tank be prerinsed or presteamed as appropriate and the wastewater segregated from wastewaters to be discharged to the POTW and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (iv) All spent cleaning solutions, including interior caustic washes, interior presolve washes, interior detergent washes, interior acid washes, and exterior acid brightener washes shall be segregated from other wastewaters and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (v) Provisions for appropriate recycling or reuse of cleaning agents; (vi) Provisions for minimizing the use of toxic cleaning agents (solvents, detergents, or other cleaning or brightening solutions); (vii) Provisions for appropriate recycling or reuse of segregated wastewaters (including heels and prerinse/pre-steam wastes); (viii) Provisions for off-site treatment or disposal, or effective pre-treatment of segregated wastewaters (including heels, prerinse/pre-steam wastes, spent cleaning solutions); (ix) Information on the volumes, content, and chemical characteristics of cleaning agents used in cleaning or brightening operations; and (x) Provisions for maintaining appropriate records of heel management procedures, prerinse/pre-steam management procedures, cleaning agent management procedures, operator training, and proper operation and maintenance of any pre-treatment system. [65 FR 49700, Aug. 14, 2000, as amended at 70 FR 5061, Feb. 1, 2005] Subpart B—Rail Tank Cars Transporting Chemical and Petroleum Cargos top § 442.20 Applicability. top This subpart applies to discharges resulting from the cleaning of rail tank cars which have been used to transport chemical or petroleum cargos. § 442.21 Effluent limitations attainable by the application of the best practicable control technology currently available (BPT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BPT: Table_Effluent Limitations ------------------------------------------------------------------------ Maximum Regulated parameter Maximum monthly daily \1\ avg. \1\ ------------------------------------------------------------------------ BOD5......................................... 61 22 TSS.......................................... 58 26 Oil and grease (HEM)......................... 36 16 Fluoranthene................................. 0.076 Phenanthrene................................. 0.34 pH........................................... (\2\) (\2\) ------------------------------------------------------------------------ \1\ Mg/L (ppm). \2\ Within 6 to 9 at all times. § 442.22 Effluent limitations attainable by the application of the best conventional pollutant control technology (BCT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BCT: Limitations for BOD5, TSS, oil and grease (HEM) and pH are the same as the corresponding limitation specified in §442.21. § 442.23 Effluent limitations attainable by the application of best available technology economically achievable (BAT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BAT: Limitations for fluoranthene, phenanthrene, and oil and grease (HEM) are the same as the corresponding limitation specified in §442.21. § 442.24 New source performance standards (NSPS). top Any new point source subject to this subpart must achieve the following performance standards: Standards for BOD5, TSS, oil and grease (HEM), fluoranthene, phenanthrene and pH are the same as the corresponding limitation specified in §442.21. § 442.25 Pretreatment standards for existing sources (PSES). top (a) Except as provided in 40 CFR 403.7 and 403.13 or in paragraph (b) of this section, no later than August 14, 2003 any existing source subject to this subpart which introduces pollutants into a publicly owned treatment works must achieve PSES as follows: Table_Pretreatment Standards' ------------------------------------------------------------------------ Maximum Regulated parameter daily \1\ ------------------------------------------------------------------------ Non-polar material (SGT-HEM).............................. 26 Fluoranthene.............................................. 0.076 Phenanthrene.............................................. 0.34 ------------------------------------------------------------------------ \1\ Mg/L (ppm). (b) As an alternative to achieving PSES as defined in paragraph (a) of this section, any existing source subject to paragraph (a) of this section may have a pollution prevention allowable discharge of wastewater pollutants, as defined in §442.2, if the source agrees to a control mechanism with the control authority as follows: (1) The discharger shall prepare a Pollutant Management Plan that satisfies the requirements as specified in paragraph (b)(5) of this section, and the discharger shall conduct its operations in accordance with that plan. (2) The discharger shall notify its local control authority prior to renewing or modifying its individual control mechanism or pretreatment agreement of its intent to achieve the pollution prevention allowable discharge pretreatment standard by submitting to the local control authority a certification statement of its intent to utilize a Pollutant Management Plan as specified in paragraph (b)(1) of this section. The certification statement must be signed by the responsible corporate officer as defined in 40 CFR 403.12(l); (3) The discharger shall submit a copy of its Pollutant Management Plan as described in paragraph (b)(1) of this section to the appropriate control authority at the time he/she applies to renew, or modify its individual control mechanism or pretreatment agreement; and (4) The discharger shall maintain at the offices of the facility and make available for inspection the Pollutant Management Plan as described in paragraph (b)(1) of this section. (5) The Pollutant Management Plan shall include: (i) Procedures for identifying cargos, the cleaning of which is likely to result in discharges of pollutants that would be incompatible with treatment at the POTW; (ii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that heels be fully drained, segregated from other wastewaters, and handled in an appropriate manner; (iii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that the tank be prerinsed or presteamed as appropriate and the wastewater segregated from wastewaters to be discharged to the POTW and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (iv) All spent cleaning solutions, including interior caustic washes, interior presolve washes, interior detergent washes, interior acid washes, and exterior acid brightener washes shall be segregated from other wastewaters and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (v) Provisions for appropriate recycling or reuse of cleaning agents; (vi) Provisions for minimizing the use of toxic cleaning agents (solvents, detergents, or other cleaning or brightening solutions); (vii) Provisions for appropriate recycling or reuse of segregated wastewaters (including heels and prerinse/pre-steam wastes); (viii) Provisions for off-site treatment or disposal, or effective pre-treatment of segregated wastewaters (including heels, prerinse/pre-steam wastes, spent cleaning solutions); (ix) Information on the volumes, content, and chemical characteristics of cleaning agents used in cleaning or brightening operations; and (x) Provisions for maintaining appropriate records of heel management procedures, prerinse/pre-steam management procedures, cleaning agent management procedures, operator training, and proper operation and maintenance of any pre-treatment system; § 442.26 Pretreatment standards for new sources (PSNS). top (a) Except as provided in 40 CFR 403.7 and 403.13 or in paragraph (b) of this section, any new source subject to this subpart which introduces pollutants into a publicly owned treatment works must achieve PSNS as follows: Table_Pretreatment Standards ------------------------------------------------------------------------ Maximum Regulated parameter daily \1\ ------------------------------------------------------------------------ Non-polar material (SGT-HEM).............................. 26 Fluoranthene.............................................. 0.076 Phenanthrene.............................................. 0.34 ------------------------------------------------------------------------ \1\ Mg/L (ppm). (b) As an alternative to achieving PSNS as defined in paragraph (a) of this section, any new source subject to paragraph (a) of this section may have a pollution prevention allowable discharge of wastewater pollutants, as defined in §442.2, if the source agrees to a control mechanism with the control authority as follows: (1) The discharger shall prepare a Pollutant Management Plan that satisfies the requirements as specified in paragraph (b)(5) of this section, and the discharger shall conduct its operations in accordance with that plan. (2) The discharger shall notify its local control authority prior to obtaining, renewing, or modifying its individual control mechanism or pretreatment agreement of its intent to achieve the pollution prevention allowable discharge pretreatment standard by submitting to the local control authority a certification statement of its intent to utilize a Pollutant Management Plan as specified in paragraph (b)(1) of this section. The certification statement must be signed by the responsible corporate officer as defined in 40 CFR 403.12(l); (3) The discharger shall submit a copy of its Pollutant Management Plan as described in paragraph (b)(1) of this section to the appropriate control authority at the time he/she applies to obtain, renew, or modify its individual control mechanism or pretreatment agreement; and (4) The discharger shall maintain at the offices of the facility and make available for inspection the Pollutant Management Plan as described in paragraph (b)(1) of this section. (5) The Pollutant Management Plan shall include: (i) Procedures for identifying cargos, the cleaning of which is likely to result in discharges of pollutants that would be incompatible with treatment at the POTW; (ii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that heels be fully drained, segregated from other wastewaters, and handled in an appropriate manner; (iii) For cargos identified as being incompatible with treatment at the POTW, the Plan shall provide that the tank be prerinsed or presteamed as appropriate and the wastewater segregated from wastewaters to be discharged to the POTW and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (iv) All spent cleaning solutions, including interior caustic washes, interior presolve washes, interior detergent washes, interior acid washes, and exterior acid brightener washes shall be segregated from other wastewaters and handled in an appropriate manner, where necessary to ensure that they do not cause or contribute to a discharge that would be incompatible with treatment at the POTW; (v) Provisions for appropriate recycling or reuse of cleaning agents; (vi) Provisions for minimizing the use of toxic cleaning agents (solvents, detergents, or other cleaning or brightening solutions); (vii) Provisions for appropriate recycling or reuse of segregated wastewaters (including heels and prerinse/pre-steam wastes); (viii) Provisions for off-site treatment or disposal, or effective pre-treatment of segregated wastewaters (including heels, prerinse/pre-steam wastes, spent cleaning solutions); (ix) Information on the volumes, content, and chemical characteristics of cleaning agents used in cleaning or brightening operations; and (x) Provisions for maintaining appropriate records of heel management procedures, prerinse/pre-steam management procedures, cleaning agent management procedures, operator training, and proper operation and maintenance of any pre-treatment system; Subpart C—Tank Barges and Ocean/Sea Tankers Transporting Chemical and Petroleum Cargos top § 442.30 Applicability. top This subpart applies to discharges resulting from the cleaning of tank barges or ocean/sea tankers which have been used to transport chemical or petroleum cargos. § 442.31 Effluent limitations attainable by the application of the best practicable control technology currently available (BPT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BPT: Table_Effluent Limitations ------------------------------------------------------------------------ Maximum Regulated parameter Maximum monthly daily \1\ avg. \1\ ------------------------------------------------------------------------ BOD5......................................... 61 22 TSS.......................................... 58 26 Oil and grease (HEM)......................... 36 16 Cadmium...................................... 0.020 ........... Chromium..................................... 0.42 ........... Copper....................................... 0.10 ........... Lead......................................... 0.14 ........... Mercury...................................... 0.0013 ........... Nickel....................................... 0.58 ........... Zinc......................................... 8.3 ........... pH........................................... (\2\) (\2\) ------------------------------------------------------------------------ \1\ Mg/L (ppm). \2\ Within 6 to 9 at all times. § 442.32 Effluent limitations attainable by the application of the best conventional pollutant control technology (BCT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BCT: Limitations for BOD5, TSS, oil and grease (HEM) and pH are the same as the corresponding limitation specified in §442.31. § 442.33 Effluent limitations attainable by the application of best available technology economically achievable (BAT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BAT: Limitations for cadmium, chromium, copper, lead, mercury, nickel, and zinc are the same as the corresponding limitation specified in §442.31. § 442.34 New source performance standards (NSPS). top Any new point source subject to this subpart must achieve the following performance standards: Standards for BOD5, TSS, oil and grease (HEM), cadmium, chromium, copper, lead, mercury, nickel, zinc and pH are the same as the corresponding limitation specified in §442.31. § 442.35 Pretreatment standards for existing sources (PSES). top Except as provided in 40 CFR 403.7 and 403.13, any existing source subject to this subpart must achieve the following pretreatment standards: Table_Pretreatment Standards ------------------------------------------------------------------------ Maximum Regulated parameter daily \1\ ------------------------------------------------------------------------ Non-polar material (SGT-HEM).............................. 26 Cadmium................................................... 0.020 Chromium.................................................. 0.42 Copper.................................................... 0.10 Lead...................................................... 0.14 Mercury................................................... 0.0013 Nickel.................................................... 0.58 Zinc...................................................... 8.3 ------------------------------------------------------------------------ \1\ Mg/L (ppm). § 442.36 Pretreatment standards for new sources (PSNS). top Except as provided in 40 CFR 403.7, any new source subject to this subpart must achieve the following pretreatment standards: Standards for non-polar materials (SGT-HEM), cadmium, chromium, copper, lead, mercury, nickel and zinc are the same as the corresponding standard specified in §442.35. Subpart D—Tanks Transporting Food Grade Cargos top § 442.40 Applicability. top This subpart applies to discharges resulting from the cleaning of tank trucks, intermodal tank containers, rail tank cars, tank barges and ocean/sea tankers which have been used to transport food grade cargos. If wastewater generated from cleaning tanks used to transport food grade cargos is mixed with wastewater resulting from cleaning tanks used to transport chemical or petroleum cargos, then the combined wastewater is subject to the provisions established for the corresponding tanks (i.e., truck, railcar or barge) in Subparts A, B, or C of this part. § 442.41 Effluent limitations attainable by the application of the best practicable control technology currently available (BPT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BPT: Table_Effluent Limitations ------------------------------------------------------------------------ Maximum Regulated parameter Maximum monthly avg. daily \1\ \1\ ------------------------------------------------------------------------ BOD5......................................... 56 24 TSS.......................................... 230 86 Oil and grease (HEM)......................... 20 8.8 pH........................................... (\2\) (\2\) ------------------------------------------------------------------------ \1\ Mg/L (ppm). \2\ Within 6 to 9 at all times. § 442.42 Effluent limitations attainable by the application of the best conventional pollutant control technology (BCT). top Except as provided in 40 CFR 125.30 through 125.32, any existing point source subject to this subpart must achieve the following effluent limitations representing the application of BCT: Limitations for BOD5, TSS, oil & grease (HEM) and pH are the same as the corresponding limitation specified in §442.41. § 442.43 Effluent limitations attainable by the application of best available technology economically achievable (BAT). [Reserved] top § 442.44 New source performance standards (NSPS). top Any new point source subject to this subpart must achieve the following performance standards: Standards for BOD5, TSS, oil and grease (HEM) and pH are the same as the corresponding limitation specified in §442.41.